Crown Com-Tech CT-400 Wartungshandbuch Seite 27

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 39
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 26
Com-Tech 400 Amplifier Service Manual
27
Q43188-4 Output Module (P10396-3 board) Parts List Cont.
Capacitors
C01 C 8511-5 .047µF 250V Ax
C02 C 8426-6 .1µF
C03 C 8426-6 .1µF
C04 C 6805-3 .022µF
C05 C 6805-3 .022µF
C06 C 6806-1 .01µF 100V Ax
C07 C 6807-9 .001µF 100V Ax
C08 C 6810-3 180pF
C09 C 6809-5 220pF
C43 C 7697-3 .01µF Disc
Diodes
D01 C 2851-1 1N4004
D02 C 2851-1 1N4004
D03 C 2851-1 1N4004
D04 C 2851-1 1N4004
D05 C 2851-1 1N4004
D06 C 2851-1 1N4004
D07 C 2851-1 1N4004
D08 C 2851-1 1N4004
D09 C 2851-1 1N4004
D10 C 2851-1 1N4004
D11 C 2851-1 1N4004
D12 C 2851-1 1N4004
Inductors
L00 C 6592-6 1.3µH Output Coil
L01 C 3510-2 470µH
L02 C 3510-2 470µH
Transistors
Q17 C10155-7 NPN 2SC4793
Q19 C10156-5 PNP 2SA1837
Note: Q18, S100, Driver Transistors, and Output Tran-
sistors are not included with Output Module. See
Output Assembly parts list for part numbers.
Resistors
R00 A10266-4711 470
R01 A10266-1011 100
R04 C 6486-2 .2 5W
R07 C 6486-2 .2 5W
R10 A10266-1011 100
R11 A10266-2R73 2.7 1W
R12 A10266-2R73 2.7 1W
R13 A10266-4711 470
R14 A10266-2R73 2.7 1W
R16 C 6486-2 .2 5W
R19 C 6486-2 .2 5W
R23 C 6844-2 250 Pot LS Bias
R24 A10266-1331 13K
R25 A10266-2221 2.2K
R26 C 6844-2 250 Pot HS Bias
R27 A10266-3911 390
R28 A10266-1331 13K
R29 A10266-5101 51
R30* A10265-10201* 102* 1%
R31 C 3614-2 15 .5W
R32 C 3614-2 15 .5W
R33 C 7779-9 22 .5W Flame Proof
R34 C 7779-9 22 .5W Flame Proof
Misc.
Board P10396-3
Z1-Z7, Z9 C 5868-2 0 Ohm Jumper
Z8 A10124-24 Solid Wire
Clips D 6414-3 Q17/Q19 Hold Down
J500 J600 C 7057-0 10 Pin Header
*Note: R30 is 102 Ohms in most units, though in some
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).
Seitenansicht 26
1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 38 39

Kommentare zu diesen Handbüchern

Keine Kommentare